Boot Cleaning Machine Boot Cleaner Machine for Air Shower Room N-SJ2850
1.Completely automatic design.
2.The quickest response speed.
3.User time and energy is saved.
5.Excellent cleaning and disinfecting effects.
6.Extended service life.
7.Convenient cleaning management.
How to add water and drain sewage of Boot Cleaning Machine in Air Shower Rooms
The boot cleaning machine N-SJ2860 is especially designed for air shower rooms.This boot cleaner machine is built inside the air shower room. So, many new users may doubt how to add water and drain sewage efficiently. Don’t worry, let me explain the 2 ways of waste drainage to you step by step. I believe you will have a better understanding of our shoe sole cleaner machine after reading the article.
1. Automatic Mode of Automatic Boot Cleaning Machine
The boot cleaning machine has automatic water inlet and drain function. In case of automatic water change, you need to connect the inlet and drain pipe inside the cleanroom.
1.1 Installation Methods:
1) Pull the inlet and drain hose to the boot cleaner machine.
The water inlet pipe has an external diameter of 20mm. And the drain pipe has an external diameter of 25mm. However, the connectors are all fitted for the water inlet pipes.
2) The pipework can be directed towards the ceiling or the floor.
The boot cleaner machine is equipped with a high-pressure pump with a lift of 10-15 meters. The pipework can also be routed to the floor. But if it is led to the floor, the drain outlet should be positioned about 1-2 cm above the machine, so as to avoid self-priming water backflow.
Attention: If more than one boot cleaner machine is used at the same time, the drain can’t be connected in parallel. If the water inlet is connected to the PVC pipe, you should drain half a bucket of water until the water pipe is empty of impurities and sediments. And then dock the water inlet pipe to stop debris and glue from clogging the water inlet solenoid valve.
3) After the installation of the inlet and outlet pipes, place the bottom shoe cleaner flat on the ground.
The machine has two pipes with an external diameter of 20mm and 1.5-metre length. They are connected to the water inlet and drain outlet. The water inlet and outlet are respectively at the rear of the equipment on the left and right sides. The water inlet solenoid valve is docked to the water inlet pipe, and the water pump is mated to the drainage pipe.
Finally, adjust the boot cleaning machine into a horizontal state. After installing the handrails, check whether the water level sensor is flat in the slot. Also, examine whether the machine inlet and drain hoses are overwhelmed or bent. And finally plug the boot cleaner machine’s electricity leakage protection plug to the power supply.
4) Before the whole boot cleaning machine is sold, our engineers have set all the parameters
If there is no special need, users needn’t debug again.
5) After installation and inspection, you may wonder how to clean sole of shoes.
Just press the control panel switch on the shoe cleaning equipment. After the sensor senses the human body, it starts working immediately. Step onto the cleaning area for 3-5 seconds, the ball-type brushes begin to roll back and forth, automatically remove dirt mud in the soles and sides of shoes. Then step onto the blue absorbent pad in the drying area, just to dry the residual water stains on the soles of heavy duty boots.
2. Manual Mode of Boot Cleaner Machine
If there is no water supply and sewage outlet to connect the water inlet pipe and drain pipe in the installation area, the user can use the dirt sucker for manual one-key drainage and water change.
2.1 The Specific Operation Method is as follows:
1) Open the cover, take out the suction motor.
2) Attach the suction motor to the suction pot enclosure
3) Press the suction switch
4) Place the bottom of the suction pot flat in the sink, and then push back and forth to suck dirt
5) Pour out the automatic inhalation of sewage inside the suction pot.
6) Finally add clean water to the sink.
1) When manually sucking sewage, the water shouldn’t exceed the highest water level line of the suction pot, just to avoid water damage to the suction motor.
2) Do not tilt the kettle when pouring and filling water, otherwise the water will overflow.
Besides, whether you use auto mode or manual mode, the motorized shoe cleaning machine also has some protection functions. If the boot brush stations are improperly used and maintained, then it will trigger off the self-protection functions.
3.The 5 Protection Functions of the Equipment:
1) No Water Protection:
In case of no water, the boot wash station will stop running and alarm at once)
2) Water Level Protection:
The water lever sensor can stop users from worrying about the water idling, water full overflow and other problems like water leakage. In case of water replenishment, users can set the drainage time according to the usage of the automatic boot cleaning station. Besides, the drainage interval (1-12 hours) is adjustable. Drainage water replenishment: users can adjust the frequency of passing times and drainage replenishment according to their actual needs.
3) Water Level Switch Fault Protection:
When detecting the high water level switch closed and low water level switch disconnected, the controller immediately shut down all loads.
4) Water Level Overrun Protection:
When detecting the high and low water level switches closed simultaneously, the controller prohibits automatic operation (shut down all outputs), but allows the user to press the manual switch to pump water in manual mode.
5) Add Water Overtime Protection:
If you continue to add water to reach the set time, but still can’t make the low water level switch close, then the shoe scrubber will report a fault (prohibit motor and pump operation). But the solenoid valve continues to open, once the water supply is normal, it will resume normal operation.
All in all, our automatic shoe cleaners have strong cleaning system and multiple protection functions. Users can either use auto mode or manual mode to add water and drain sewage. Besides, all our boot washing stations are made of high-quality raw materials, such as stainless steel SUS304, and Dupont nylon, etc. With a stainless steel frame, the boot washer machine won’t deform or rust. That’s why our shoe sole cleaning machines are popular among customers at home and abroad. Therefore, if you are a factory owner and want to buy industrial boot cleaners for air shower room, don’t worry about the installation and use. We will guide you step by step by sending demo videos, words and pictures. Even a non-professional worker can handle it easily. Just take action and add it to cart, and our versatile heavy duty boot scraper will be great helper for your ground cleaning!
- Dimension(MM): 2850*768*145
- Clean Zone(MM): 1715*480
- Dry Zone(MM): 975*480
- Water Absorbent Pad (MM): 975*430
- Number of passer/minute: 80 persons/minute
- Work Induction: Auto
- Inlet Water Temperature: 1-40℃
- Water Tank Capacity: 30L
- Water Change Method: Manual/Auto
- Sediment Cleaning Method: Dirt Suction
- Suction Power: AC100W
- Working Voltage: AC220V
- Working Current: 2A
- Motor Voltage/Power: AC220V/ 300W
- Pump Voltage/Power: DC24V/75W
- Pump Head: 10 Meter
- Security: Overload/leakage protection
- Brush Rotation Speed: 60RPM
- Noise: <60DB
- Main Body Material: SUS304
- Maximum Load Capacity: 500KG
- Main Body Life: 6 Years
- Weight: 200KG
- Warranty: 1 Year
- Input Voltage: We will choose the corresponding voltage model according to the destination country of your order
- Water Absorbent pad *3
- Power Supply Line *1
- DC Converter *1
- Suction Motor *3
- Sole Cleaning Machine *1
Frequently Asked Questions about Shoe Cleaning Machine N-SJ2850
Q1: Is N-SJ2850 a shoe cleaning machine for home?
A1: No, it isn’t. Usually, the shoe cleaner machine is used for air shower room and cleanroom. If you want to buy one for home, you can choose the G-SJ1004 or G-SJ1005, which is a much more cost-effective solution.
Q2: When cleaning muddy shoes, should I add some shoe cleaners to the sink?
A2: Normally, the boot washing station can wash and dry your shoe soles well. If you want better cleaning effects, you can also add some shoe cleaner or shoe whitener to the sink.
Q3: Could you tell me how to clean muddy leather boots at home?
A3: In this case, our boot scraper is not a good choice. You might as well apply some leather boot cleaners to the soles. Use a bristle brush to clean the soles and sides thoroughly. Then put your leather boots into the UV shoe sterilizer. Then your shoes will get cleaned and sterilized at the same time.
Shoes Cleaning Machine Shoe Sole Sanitizer Machine for Air Shower Room N-SJ850$1,469.00
Best Electric Shoe Shine Machine for Cleanroom N-SJ1340$1,669.00
Roller-type Automatic Shoe Polisher with Slopes for Wheel Cleaning N-SJ1850$1,999.00
Boot Cleaning Machine Boot Cleaner Machine for Air Shower Room N-SJ2850$2,799.00